Disconnect Clip for Copper Tubing, 3/4 In.
Disconnect Clip for Copper Tubing, 3/4 In.
Disconnect Clip for Copper Tubing, 3/4 In. is rated out of 5 by 9.
1/2"disconnect clip; bagged; u712a; sharkbite push-fit fittings for use with copper tubing cts, cpvc and pex with integral tube liner included; constructed of dzr brass, certified to 200 psi and 200 degrees f, design certified to asse 1061/nsf61 standards, meets upc, ipc and cupc requirements, fitting are listed with iapmo and are certified for use on potable and hydronic water distribution, certified for underground applications and as a manufactured joint without the need for access panels.
- Lightning fast, won't let go.
- Easy installation, fast disassembly if needed.
- Use on wet or dry repairs.
- No solder, clamps, unions or glue needed.
|Country of Origin||AU|
|Manufacturer Name||SHARKBITE/CASH ACME|
|California Residents Proposition 65||www.P65Warnings.ca.govThis product can expose you to chemicals including cadmium which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to|
Rated 1 out of 5 by Jos w from Get what you pay for I bought this since I had to redo some sink piping and this tool did not do anything that it’s supposed to do. I rarely rate a product 1 star, but shark bite, which I thought was an amazing product, just fooled me with this product. Shark bite needs to come up with a better tool to undo!
Date published: 2022-06-03
Rated 3 out of 5 by WayneL from Disconnect clip is a joke Have bought Sharkbite couplings before and installed them as directed. N Haven't had a need to remove any until today. Bought two today to replace a shutoff valve and couple a water supply line to a hot water heater. Because i=of another soldered joint leaking with all the pipe movement I had to uncouple the valve from the 3/4 inch copper pipe. I worked at it for over 30 minutes then enlisted my son in law (a licensed building contractor) who took another 7 minutes to finally remove it. The orange horseshow shaped tool is worthless! Next time I need such a repair I'll either make certain there can be NO removal needed in my lifetime or go Old School and solder the joint/valve. Wished I had spent the $8 for the tong removal tool.
Date published: 2021-12-03
Rated 1 out of 5 by Asparagus from Complete fail I’ve used these and also the special plier tool. Neither of them is very effective. Best option is to use appropriately-sized crescent wrench. Just fit the wrench to the pipe or tubing, then slide against the sharkbite fitting, and pull it off. Works best for me.
Date published: 2020-03-08
Rated 2 out of 5 by tocado from Quick installation, impossible to remove I thought this was the most wonderful product until it was time to remove the SharkBite fitting. "Easy" disconnect couldn't be further from the truth. I've been wrestling with this for the last hour and it hasn't budged. I am following the instructions as well so this has nothing to do with operator error.
Date published: 2018-12-02
Rated 1 out of 5 by Harry85239 from Waste of Time and Money I was almost sold on Sharkbite, until I was forced to "undo" a fitting, using the disconnect clips. The in store demonstration of the removal process was nothing like my personal experience. In real life, I found myself in a cold and muddy 26" crawl space cutting the fitting off, like I've done, for the last two decades, except at four times the cost.
Date published: 2016-11-26
Rated 1 out of 5 by JAHMinnesota from Disconnect tool This tool is as close to worthless as you can get. A waste of time and money. Ended up cutting out four fittings to fix a defective one.
Date published: 2016-10-23
Rated 5 out of 5 by barall from Great little tool This tool is a must have when installing any Sharkbite connections. I just installed two 3/4" connections. The first one went on just great, very quickly. With the second one, the connection went in halfway and stopped. I went down to my local hardware store and picked up this tool and very quickly removed the second connector and found a little bump on the underside of the pipe that prevented complete installation. I removed the bump and successfully reinstalled the connection all the way on. Without this little tool I would have been stuck with a failed installation.
Date published: 2016-10-14
Rated 1 out of 5 by geo worker from disconnect clip I have had no success with the disconnect tool. The white tubing does not come out. Your video makes it look easy but not so. I buy additional joints to take care of leaks, but that is more $$.
Date published: 2016-07-01
Behind every project is a True Value®
Thanks for signing up!
Please add email@example.com to your address book.
This functionality is enabled only for desktop.