Ultimate Floor Finish, Clear Satin, 1-Gallon
Ultimate, gallon, crystal clear, water based satin floor finish, self cross linking technology, re-coat in 2 hours, does not require sanding between coats, exceptional flow & leveling with easy application, low odor, cleans up with soap & water, most projects can be completed in 1 day.
|Country of Origin||US|
|Manufacturer Name||MINWAX COMPANY, THE|
Rated 5 out of 5 by John455cid from Great product I'm a first time floor refinisher. I used this on the really rough condition wood floors in my first house two years ago. After sanding the floors to lightly to ensure adhesion , I applied only two coats . Three hours apart . With a wool roller sleeve !! Rolled slow and even . Great final Finnish . Picture is three days after finishing. Its been two years . Still looks great . I used what was left to refinish my wooden chairs . I will use it again when it come time .
Date published: 2021-02-06
Rated 5 out of 5 by jimbo23 from Fast hardwood floor renewal! I bought this to rejuvenate existing oak floors and I’m happy with the results! The process is very simple: a light 220 grit sanding followed by a lot of cleaning and you’re good to go. Product is very easy to apply using an applicator pad and a paint tray. Coverage was good and pleased you don’t need to sand between coats. Considered applying a third coat but it seemed unnecessary. Spendy but I think it’s a good value given the results.
Date published: 2021-02-05
Rated 5 out of 5 by Ultramontane from Bathroom Vanity Bought this product after much research into water-based finishes. I wanted something durable, easy to apply and environmentally 'friendly' to finish a vanity unit made from Australian Ash. Product appeared 'watery' in the pot but was easy to apply, (foam brush), and dried in a few hours. I lightly sanded after the first coat due to grain lift and applied 3 more coats over the following days. Couldn't be happier with the results, super hard/clear finish which really brings out the figure in the wood.
Date published: 2020-10-02
Rated 5 out of 5 by Big mike from Easy to apply works great I washed my weathered floors and put 3 coats on and they look great
Date published: 2020-06-10
Rated 5 out of 5 by Mike L from Easy to use - Great Results I've had this product for a couple years with the intention of refinishing our kitchen and dining room. When I started stirring the product I was concerned because of the thick goo that was at the bottom. It took 20-30 minutes to stir and mix in the settled product. Once I started laying the product down I was very impressed with how easy it was to use. Slow even strokes with a lambs wool applicator on a handle produced no bubbles or lines. I waited 2 hours in between coats and did 4 coats because it's a high traffic area. The results are fantastic. I highly recommend this product for ease of application. I hope it is as durable as they say it is.
Date published: 2020-04-16
Rated 5 out of 5 by Bill79 from Easy application. I went back and forth on whether to use water based or oil based finish. I didn’t really want the yellowing of oil, the extra long dry time, and the massive odor associated with oils based finishes. I read reviews, and was slightly nervous about using this product, but I has a suspicion it was more application error vs product failure, which is typical with any coatings. My suspicions were correct. I stained my floors with dark walnut stain, and three coats of minwax ultimate floor finish following the instructions meticulously, and have been extremely pleased with outcome. I have two dogs, and the finish has preformed above expectations. Always be cautious with reviews, everyone in the DIY sector thinks they are experts. This was my very first floor finish job, and I’m over joyed with the outcome, and receive compliments on my floors with every guest who walks though the door!
Date published: 2020-02-11
Rated 5 out of 5 by Frank in CT from very low odor, clean up is easy I put down a new floor with no stain, applied directly to floor. I did 3 coats waiting at least 24 hours for each coat to adhere. I sanded in between coats with 220 grit. I noticed all the complaints were from people that had stained the floor first. so I can't speak for that process but its great for directly on a floor that has no stain.
Date published: 2020-02-07
Rated 5 out of 5 by Sarah from Easy to apply and looks beautiful Sanded floors 100 year old maple wood floors with drum sander and edger 20-60-100 grit. Floors had a lot of waxy buildup. Removed completely. Vacuumed room and washed walls. Applied two coats of the water-based Minwax Ultimate Floor Finish, glossy first and final coat with satin. No sanding in between coats as they were done within 24 hours. We will be applying one more coat in a few minutes, but very impressed so far. Water-based polyurethane cannot be directly applied to stained floors which is why I think some reviewers are having trouble with this product. We applied this product to bare wood. Attached is a before (before sanding and urethane) picture and an after.
Date published: 2020-01-15
Behind every project is a True Value®
Thanks for signing up!
Please add email@example.com to your address book.
This functionality is enabled only for desktop.